16 Must-Read Fireplace Safety Tips

Fireplaces might add the ambiance of warmth and tranquility to your home, but that cozy, crackling glow also conceals an ash pan of potential problems. Cinders, ash, volatile resins and creosote that are not routinely cleared from the fireplace can pose a dangerous fire hazard. Plus, what do you do if you don’t want to have a fire burning? How can a homeowner maintain their fireplace correctly and safely while preventing their heating dollars from going up in smoke?

Because caring for chimneys and fireplaces can be both complicated and dirty, we’ve put together a list of tips to keep your home warm and safe.

Fireplace Care Tips

The first place to prevent problems with your fireplace or wood stove is to select the right kind of wood. Use dried and well-seasoned wood that burns hot and completely enough so that it produces less creosote and carbon monoxide.

How to Choose the Right Fuel for your Fireplace

  1. Don’t use chemicals. Fire and chemicals don’t mix! Never use gasoline, kerosene, or charcoal starter. Don’t burn painted, pressure-treated, or plywood. These can give off a whole slew of toxic chemicals that could enter your living space.
  2. Avoid using wet, rotten, diseased, or moldy wood. Only start fires with dry kindling, newspaper, or pine cones. Pine cones contain natural resins that burn quickly and are hot enough to ignite firewood. Dry wood also burns more completely than wet.
  3. Check the moisture content. Moisture content determines how much creosote will form in your chimney. Use wood that has been seasoned for 12 months and has a moisture content of less than 20%. Firewood moisture meters are available from most home centers.
  4. Only use local firewood.This prevents the spread of tree diseases and insect pests to your neighborhood. The emerald ash borer has killed 50 million ash trees in the US just by being moved around in firewood.
  5. Store your wood properly. When you buy firewood, store it for use next year. That way, you can be sure it’s properly dried. Store your freshly cut and stacked firewood off the ground. Keep it covered on top but leave the side open for air to circulate.
  6. Choose the right wood. Different types of wood burn differently. Oak and other hard woods generally burn long and hot. Soft woods, like pine, will burn fiercely hot but very fast. If soft woods are not properly dried, the water content in their resins can release high amounts of creosote.
  7. Keep your fireplace clean. This allows better air flow and cleaner combustion. Wood burning fireplaces emit 28 lbs of particulate emissions (soot and ash) per MMBtus of heat output.
  8. Always keep a fire extinguisher handy. A single spark can start a house fire —so it’s best to be prepared.

Chimney Care Tips

Chimney caps prevent leaves, debris, and animals from getting into your chimney and blocking it. They typically have some form of mesh that keeps debris out, lets smoke escape, and also arrests sparks to prevent them from starting fires outside your home. At least once a year, check over the chimney cap.

How to Check Your Chimney Cap

  1. Make sure the chimney cap is securely attached to the chimney.
  2. Make sure the chimney cap’s mesh covering is intact and that no debris or animals are able to get through it.
  3. Cut back any tree limbs overhanging your chimney. Apart from the obvious fire hazard but they can also knock into the chimney during storm and damage it or the chimney cap.
  4. Check the chimney masonry. Loose or cracked brickwork should be repaired before it gets worse. You might want to contact a professional bricklayer.

Recently cracked and discolored masonry or a warped chimney cap are signs of a chimney fire. Creosote flakes or ash are strong indicators that creosote build up in your chimney has reached a danger point. Creosote fires in fireplace flues and chimneys can reach 2000°F — hot enough to easily melt metal liners, fracture brickwork, and spread flames into your attic.

If you discover evidence of a chimney fire, you’ll want to get you chimney inspected and cleaned by a professional chimney sweep as soon as possible. Trained chimney sweeps can show you how well your fireplace or woodstove is working and recommend how to get the most heat out of it safely.

Smoke Gets in Your Eyes —Backdrafts

The heat generated in fireplaces and woodstoves pulls air from inside your home (also called the “stack effect”) and shoots hot air and gasses out the chimney. In some newer homes that are tightly sealed or those that were not built for fireplaces, the fire may be unable to draw enough air for the wood smoke to go up the chimney. This is known as backdrafting or negative pressure. Consequently, smoke, cinders, creosote, and dangerous carbon monoxide will be trapped in the home.

A similar problem happens when there are furnace return vents in the same room as the fireplace. As the HVAC sucks in air for the blower, it will also pull air from the room with the fireplace. This negative pressure stops smoke from going up the chimney. The same thing can happen if there’s a clothes dryer running that is blowing air out of the house. While closing off the HVAC return vent or avoid running the clothes dryer while you have a fire going are temporary fixes, it’s best to add a fresh air supply to your fireplace or wood stove. If you already have a fresh air supply for your fireplace, be sure to keep it clean so that ash and other debris don’t block it off.

Fireplace Dampers

Fireplace dampers are designed to control the flow of exhaust from the fire. Many traditional fireplaces have built-in dampers (also called “throat dampers “) at the mouth of the flue. If you don’t want to have a fire, then ideally, you can close the damper and keep out the cold weather. Over time, however, creosote and ash deposits will build up and prevent the damper from closing (or opening) properly. To test your fireplace damper, hold a lit candle in the fireplace with the damper closed. If the flame flickers, the damper isn’t able to close all the way and heated air from your home is going up the chimney.

Unfortunately, because most fireplace throat dampers leak along their entire width of the fireplace, it’s better to try some alternatives. You can install a chimney-top damper that fully seals your chimney. It looks much like a hatch and uses a heat-resistant gasket. Another easier and inexpensive fix is to use an inflatable fireplace damper balloon that gets stuffed inside the chimney to cut drafts.




When to Start Packing for a Move: Moving day

Make sure you have what you need. Whether you’re driving down the street or flying to a new continent, make sure you have all the necessities for your transit.

Double-check your home for forgotten items. A final walk-through can ensure you don’t leave anything behind. Don’t forget the outdoors.

Review the paperwork. Carefully read the moving paperwork you’ll be signing, and double-check the moving fees to make sure everything is on the level.

Thank the movers. Prepare some refreshments for them, and keep cash on hand for a tip if you’re satisfied with their work. Common practice is to tip each mover $4-$5 for every hour they work.

Share your info. Give the truck driver your exact new address and phone number to ensure your stuff makes it to the right location.

Clean up. Now that the place is empty, leave it the way you’d want to find it as a new owner.

Say goodbye to your old home. Lock it up and bid it farewell. The time has come to set foot on the road to your new life! Snap some pics or take a video as tribute.

While many tasks are common for residential moves, certain aspects of your move may be unique and require a different approach. Personalize this moving timeline to make it work just right for you.

Related Stories




When to Start Packing for a Move: Moving day Make sure you have what you...

How to Automate Your Home Appliances That Use the...

Automating your home appliances that use the most energy can help you save money...

Planning on Buying a Home? Do These 10 Things...

From assembling your team to making your wish list, here's how to get your...


When to Start Packing for a Move: Moving day Make sure you have what you...


When to Start Packing for a Move One week before moving day Contact your moving company....


When to Start Packing for a Move: Two days before moving day Finish packing. Get everything in...

Popular Categories

Translate »